鄂尔多斯附近有没有服务

News Center

Current location: home page  >  News Center

+Direct selling of stainless steel air shower in Huadian

But in most people's impression, only?

Low cleaning flow rate (5%) is the flash point of the system, which can significantly reduce gas cooling and heating energy consumption. The moisture in the drying room mainly comes from the human body, the water contained in the negative electrode, and the gas brought in by the air shower switch. Therefore, it is necessary to research and invent the gas flow to ensure that the humidity of the gas flowing out of the drying room is controlled at 100ppm or lower. Single air shower

Entrance procedure: wear anti-static clean clothes → open the front door, personnel enter → the air shower room starts to blow, the wind speed is as high as 20m / s At this time, when the front door is opened for more than 10 seconds, the front door can not be opened by the user, and the door can not be opened automatically after the front door is opened The process of personnel / goods going out → entering the door is finished.

The air shower door is equipped with multi wing forward low noise fan to suck the air in the air shower room through the pre filter. After entering, it is pressed into the static pressure chamber, and then pressed out by the high-efficiency air filter. The air is purified through two-stage filtration. The purified air is ejected from the nozzles in the left and right directions of the box, blowing down the dust on the person and being sucked by the fan together with the air. In this way, the high-efficiency air is blown out through the filter.

The air inlet nozzle is installed at the output end of the air inlet pipe. In addition, the air inlet nozzle is located under the top plate, and the air outlet pipe is installed on the right side plate. In addition, the input end of the outlet air duct is connected with the area under the screen plate, and the outlet fan is installed on the air outlet pipe; the upper fixed plate 12, the upper spring 13, the upper splint 14, the lower fixed plate, the lower spring and the lower splint, the upper fixed plate and the lower fixed plate The left end of the plate is connected with the right wall of the right plate, the top of the upper spring is connected with the upper fixed plate, the bottom end of the upper spring is connected with the upper splint, the bottom end of the lower spring is connected with the lower fixed plate, and the top end of the lower spring is connected with the lower splint.

A second sieve plate 24 is arranged inside the treatment box to separate the treatment box into a left chamber and a right chamber. A cleaning opening is arranged on the left wall of the treatment box, and a cover 25 is arranged at the cleaning opening. The ventilation pipe and the cleaning opening are connected with the left chamber, and the air inlet pipe is connected with the right chamber, which can improve the dust removal effect. It should be pointed out that ordinary technical personnel in the technical field should also make some improvements and modifications without departing from the technical principle, and these improvements and variants should also be regarded as the scope of protection of the technology.

Automatic air shower room, voice air shower room, stainless steel air shower room, double air shower room, single air shower room, corner air shower room, etc. Can you make non-standard air shower room according to your requirements (size, accessories, material, etc.)?

This is not only the investment cost of the drying room, but also the equipment used for battery development and production in the drying room, such as winder, liquid injection machine, sealing machine and other equipment in the drying room. The homogenization, coating, rolling and cutting equipment of lithium-ion battery electrodes are often several million. Therefore, the lithium-ion battery industry is not only a technology intensive industry, but also a capital intensive industry. Investment in lithium-ion battery industry requires a strong capital base and strong technical support. Of course, the cost ratio of the air shower room in the lithium-ion battery drying room is quite small, which is only a small part of it. There are also necessary equipment.

A second sieve plate is arranged inside the processing box to separate the treatment box into a left chamber and a right chamber. A cleaning opening is arranged on the left wall of the processing box, and a baffle cover is arranged at the cleaning opening. The ventilation pipe and the cleaning opening are communicated with the left chamber, and the air inlet pipe is connected with the right chamber. Compared with the prior art, the utility model has the following beneficial effects: through the setting described above, the air outlet pipe can be implemented through the upper and lower splints, the upper spring and the lower spring can be used for buffering, and the upper connecting plate and the right connecting plate can be designed and customized to facilitate the handling and placing of the clapboard. The dust removal air shower chamber can control the release of the left pressing plate and the right pressing plate by rotating the left screw pipe and the right screw pipe after taking off the partition plate, so as to complete the removal and cleaning of the sieve plate, which is more convenient to use.

The utility model provides a dust removal air shower chamber which is convenient to dismantle the sieve plate and is more convenient to use. In addition, the direct selling of + stainless steel air shower chamber can improve the reliability of use. Ben The dust removal air shower chamber consists of a left side plate, a bottom plate, a top plate and a partition board with mesh. The top ends of the left side plate and the right side plate are respectively connected with the left side and the right side of the bottom end of the top plate. The bottom ends of the left side plate and the right side plate are respectively connected with the left side and the right side of the top plate of the bottom plate. The screen plate is arranged under the partition board, and the air inlet fan, the air inlet pipe, the air inlet nozzle, the air outlet pipe and the air outlet fan are also included The pipe is installed at the input end of the air inlet fan, and the air inlet nozzle is installed at the output end of the air inlet pipe. In order to solve the technical problems mentioned above, the air inlet nozzle is located under the top plate of the right threaded pipe, and the top of the right threaded rod is inserted and screwed into the inner side of the bottom end of the right screw pipe. The bottom end of the right screw rod is connected with the top of the right pressure plate. The left end of the sieve plate is clamped between the left pressing plate and the left supporting plate, the right end of the sieve plate is clamped between the right pressing plate and the right supporting plate, and the left and right sides of the bottom end of the partition board are divided into two parts Do not contact the top of the left and right connecting plates.

The application of air shower in lithium-ion battery drying room is due to the development of electric vehicle industry in China, which has formed a huge market demand for lithium-ion battery. Many battery manufacturers have also expanded their production capacity. Some enterprises have also taken advantage of this trend to enter the lithium-ion battery industry. As an industry person, bacclean knows well that lithium-ion battery industry Not so beautiful, first of all, there is a lot of expenditure on the lithium-ion battery factory. Yesterday, bacclean mainly analyzed the application of air shower in the drying room of lithium-ion battery factory.

The air shower door is divided into manual and automatic air shower doors. The manual air shower door shall prevail. The current automatic air shower door is fully automatic door opening voice prompt completion, which is very convenient and fast.


Last article: Air shower room automatic door single air shower room

Last article: Purification equipment Co., Ltd

Recommended products

What's new